I will be using an 11”x11” q-snap for this example. The strip of fabric should measure 46”x6”. I happened to have a yard and a half of fabric so I was able to cut one strip. So for my 11 x 11 frame I would cut two length of elastic that measure 24 inches Dimensions for Q-snap sizes / combinations (all sizes in inches) Never heard of a needle minder? You can make your own fabric covered needle minder and have a matching set!

The length of the elastic will be roughly half of the fabric length. Then add 2 inches to sew a 1″ overlap. We need 2 pieces of elastic. I was always a die-hard hoop stitcher but recently starting using Q-snap’s and am now completely converted! Q-snap covers or “Grime Guards” as many people call them are useful for protecting and keeping your fabric clean while working on a project and also holding the excess fabric on a larger project out of the way. I recently bought one that was Q-snap’s own brand and although it works it was a little too snug and so did not hold the excess fabric easily so I decided to try making my own while I was visiting my mum (and her sewing machine!). They are actually very easy to make as it is only a seam and two long hems. The width of fabric is mostly personal preference. This number depends on if you want to be able to stuff a lot of fabric under your grime guard. I recommend the width being 5.5-6 inches. Again, this number will change according to your liking. My seam allowances for the casing ended up being slightly bigger than anticipated, leaving me less room around my q-snap. I may try a wider width of fabric and using thinner elastic. Finding the Measurement for a HoopAs you can see starting with a wider piece of fabric allows much more room within the guard to contain all the excess fabric while you stitch If you don’t mind seeing the raw edge of your fabric, fold over once and adjust your measurements accordingly. After sewing the seams together I pressed the seam open. You can sew these flaps down, but I found it unnecessary. 4. Create the casing for the elastic Grime guards are a great way to keep your projects clean, hold your needle, and store extra fabric.

Suitable for most motorcycle makes and models (except single-sided swingarm motorcycles). Cut Moto Grime Guard to size to fit your specific motorcycle make and model. The width required will be the same for all the options above - the width needs to be enough to go around the tube, hold excess fabric and also allow for the hem on either side where the elastic is sewn into the loop. I estimated that the cover that I had previously bought was just over 4 inches so I am going to use 8 inchesPut the edges together with the print on the inside and sew a seam to join the two ends to form a continuous circle of fabric (about 1.5 cm from the edge) Drivetrain Cleaner instantly blasts away contaminants on the chain and chainrings to effectively eliminate grease and grime. It also protects using our in house designed moisture repellent formulation and rust inhibitors to keep moving components in optimum working condition. The Tru-Tension Tungsten lubricants are the world first cycle lubricants of their kind. Revolutionising lubrication in the cycling industry through faster, harder wearing lubrication for any weather. Up to 40% faster than standard Ceramic and Teflon based lubricants, our lubricants are the perfect selection for riders looking for a smoother ride and improved efficiency. x 17 frame - 70 inches fabric (with this length you would likely need to sew two strips of fabric together)

Sew down the seams. Don’t forget to leave an opening so that you can put in the elastic. 5. Threading Through the Elastic For a rectangular frame you would take the length of two sides and add 2 inches, such as 8 + 11 + 2 = 21 inches Moto Grime Guard protects important braking surfaces such as brake discs, calipers, brake pads and tyres from becoming contaminated while cleaning. Its handy tray catches all the oily run-off generated by cleaning the chain and gears, preventing staining on garage floors and driveways. Once done I would shuffle it around so that the seams of the elastic aren’t exposed. 7. Finishing the Scroll Frame Grime Guards.

Put a safety pin on one end. The safety pin will make it easier to push the elastic. This will take some time and patience. It’s no fun constantly fighting with your fabric to cooperate and maybe accidentally stitching through the additional cloth. These are a fun way to accessorize your cross stitch with so many patterns to choose from. Create grime guards that match the seasons or match your projects. Even rolling up your fabric and clamping them with binder clips, the extra fabric can still get in the way.

Now you need to create a hem on either side that is wide enough for you to thread the elastic through later. Fold a small hem over followed by a larger one (about 1 cm) and iron these flat. Having the additional fold inside your hem will prevent fraying of the fabric over time as you are using the guard. You can then pin the two hems in place while you sew. NOTE: always place your pins at a 90 degree angle to the direction in which you will be sewing so that they are easy to remove later and also prevents damage to the machine needle. Moto Grime Guard protects important braking surfaces such as brake discs, callipers, brake pads and tyres from becoming contaminated while cleaning. Its handy tray catches all the oily run-off generated by cleaning the chain and gears, preventing staining on garage floors and driveways. I have done this on smaller projects with longer thread. It does the job in a pinch. Storage for Your Excess Fabric Enhance every toolbox with this 9 piece Deluxe Bundle of cycling tools, cleaning products and innovative lubricants.

🇺🇸 NOW SHIPPING FROM THE USA. 🇺🇸

Once you are happy with the tension of your elastic on the guard you need to join the two ends together. If you are using wider elastic you could use the machine but as mine was only 1/4 inch I hand sewed the ends securely together Folding twice conceals the raw edge of the fabric. It will appear a little neater as well as you won’t have to deal with the frayed fabric. 3. Create the Casing for the Elastic Fold the fabric over twice 1/2 inch along the with to create the casing. Press and sew. For the scroll frames I recommend using 3/8 elastic so that the elastic is more substantial and durable. 4. Measure Your Elastic Test the length by safety pinning the ends together. Make sure that there is enough clearance to get over the knobs of the frame and that the elastic can be pulled on easily.You also don’t want your elastic to be too loose either. 5. Adding the Elastic Put a safety pin on one end of the elastic and thread through the casing. Once one side is completed go through the other side of the casing, creating a loop.